Fiber Optic Cable

DtC Fiber Optic Outdoor Duct Cable

Outdoor Fiber optic Duct-Cable, use stregth member (steel), jelly filled, fiber contained loose tube with water blocking jelly, PE sheath feature perfect UV resistant performance and environmental stress cracking resistance. The loose tube material it self has perfect hydrolysis resistance and high strength. Suggested to be use with extra HDPE duct protection.

  • Waterproof performance of optical cable is ensured by following measures: single piece of steel wire center reinforcement
  • Special waterproof compound filled inside the loose tube 100% filled cable core
  • The loose tube material itself has perfect hydrolysis resistance and high strength. The special filling paste inside the loose tube is used to protect the optical fiber
  • Perfect waterproof material could prevent optical cable from longitudinal water penetration
DtC Fiber Optic Outdoor Direct Buried Cable
DtC Fiber Optic Indoor Distribution Cable
DtC Fiber Optic Outdoor/Indoor Drop Cable

Optical Distribution Cabinet

DTC ODC Cabinet is widely applicable in FTTX access network. It provides splice, storage, termination, splitting, customer cable routing functions, which effectively solves the problem resulted by traditional distribution devices, less adaptors and patch cords, less loss rate and defect points, safer network, more capacity, convenient for cable management and upgrading, cost saving and promoting the development of optical fibers.
  • Standard case body, made of high intensity ,anti-corrosive ,anti-aging stainless steel 304 or SMC material.
  • Grounding bar of the cabinet > 1.9 mm
  • Inner frame thickness > 2mm.
  • Adapting various bad weather condition, with reliable, sealing, water-proof and damp-proof.
  • Splicing & distribution integration module with adaptor assembling ,fusion and connection, storage in integration, inserted assembling
  • Available for different type of adaptors such as FC, SC, LC
  • Adaptors assembling with deflexion of 30o to ensure fiber pigtail bending radius, with perfect control winding ring of the fiber in horizontal and vertical
  • Can be separated between outter body, inner post and pedestal part ( Stainless Steel type )

DtC ODP cabinet is for splicing, distributing and splitting the fiber to each home pass for FTTH project, this field install is design for ourdoor open field use, can be design for wallmount use also.

  • This box can be added with basement at the box bottom, floor stand type, lock design.
  • Unattached cable access for butterfly cable and fixing fittings.
  • Outdoor applications IP55.
  • Integrated splice tray and fiber management.
  • Compact structure, good dustproof property.
  • Two layers designed, available splitter space and splice cassette with pigtail.

DTC ODF solution provides flexible cabling access, expandable frame concept, integrated and superior cable management and in addition to them a future proof modular design with the highest termination capacity possible. High density side access type of module is also designed to fit a variety of termination, splice, and storage applications.

  • Standard 19” module structure, flexible in fibre expansion and operation in large capacity
  • Applied in the high access situation in the fiber access network, can deploy standard modules, such as optical power splitting and splicing module
  • Can be customise to the super large optica link resource management office, making customer’s link management and maintenance easy
  • OTB capacity can be design and customise by order request
  • Splitter module can be mount in the cabinet

DtC Multimedia Box is for user housing termination point, design especially for FTTH user homepass termination point. The Multimedia Box can be install inside wall for good looking interior, available power distribution, space holder for modem or wifi equipment installation, also can be design as house networking center point.

  • Available for wall install (inside wall)
  • Cold rolled steel, easy and smooth operation
  • Compact structure and good air flow for equipment
  • Compatibility for most of wifi modem, and has enough room for retaining patch cord and pigtail

Fiber Optic Passive Splitter

fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. DTC splitters are available in a variety of split ratios, including 1:4, 1:8, 1:16, 1:32, 1:64, etc. They also have several types, such as bare PLC splitter, blockless PLC splitter, fanout PLC splitter, mini plug-in type PLC splitter.
  • Using SC / UPC or SC / APC connector
  • Return loss ≥ 50 db
  • Operating temperature ( -10˚C) to ( +70˚C )
  • Using fiber optic Singlemode G.657.A2
  • Made from Steel or Plastic or Fiber Glass
  • Strong and Anti - Corrosion
  • Cassette type, Box type and Mini type
fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. DTC splitters are available in a variety of split ratios, including 1:4, 1:8, 1:16, 1:32, 1:64, etc. They also have several types, such as bare PLC splitter, blockless PLC splitter, fanout PLC splitter, mini plug-in type PLC splitter.
  • Connector type​​​: SC, FC, LC ( APC or UPC )
  • Operating & storage temperature​​: -40°C to +85°C
  • Standart​​​: Telcordia GR-1221 Compliant
    Telcordia GR-1221 Compliant
    ​​​G.657A2 Compliant
DTC rack mount housing is using for PLC Cassette / Modular type, easy to use just snap in each cassette inside the available slot (capacity 16 slot). this rack mount housing compatible to use in 19 inch cabinet universal.
  • Installation quick, reliable performance, stability.
  • The body made of cold-rolled steel, powder static spray.
  • 19 inches rack installation.
  • Good uniformity,in particular the application of PON.

Fiber Optic Supporting Accessories

Fiber optic patch cords suited for equipment jumper cable, cross connects, and work area connections. All patch cords are 100% factory tested to ensure performance to TIA/EIA-568-B-3 standards. FC,SC,ST,LC,MU,MTRJ and hybrid Patch Cords are available in both multimode (9/125μm and 50/125μm) and single mode cable-types, in duplex and simplex versions. The DtC range of patch cords are constructed from high quality connectors and 9/125μm OS2 - 50/125μm OM2/OM3/OM4 grade cable.

  • Low insertion loss
  • High return loss
  • Precise end face inspection by microscope
  • Environmentally stable in optical performance
  • Provides total immunity to electrical interference
  • For Telecommunication, Computer Networks, CATV networks, active device application use, for the best result.

Usage cases for pigtail, mechanical connector, adaptor and faceplate house Option usage cases with field assembly connector, adaptor and faceplate house Other option usage cases with pigtail, heat shinkable tube, adaptor and faceplate house.

  • Insertion loss for adaptor ≤0.2dB (1310nm & 1550nm)
  • Aplicable mode for Singlemode and Multimode
  • Temperature -5 deg C to +40 deg C
  • Outer port 2

DtC Fiber Optic single piece connectors are designed for quick and easy termination either on-site or in the factory. Suitable for use with both loose tube and tight buffered cable, the LC Connector is becoming the Small Form Factor (SFF) of choice. Occupying half the space of a duplex SC Connector, this product is ideal for high density applications such as Data Centres and Server Farms.

  • Improved direc fiber jointing and embedded technology
  • Ceramic parts axial self-aligned technology
  • Integrated protective cover
  • Visual operation quality, independent on light and special equipments